Видео

The best video out there. I did this years ago and it’s still holding

👍

There is a better tool for reaching under a shingle and removing or installing a nail.

Thanks. Step by step just like you showed

Terrible lighting. 🤦🏾

Did the repaire hinge still working after all these years or how long it lasted? I'm about to do mines it broke after replacing the shocks with new ones.

What about the underlayment?

Where’s the dam paper @ dude

Was there a reason you didn’t use paper under the shingles?

Hi, thanks for the video. If you put cement fork shingles, is that permanent? Im truing yo fix a shimgle leak. Akso how to remove mould ftom undrt the plywood, from the leak?

Thick coat wax protects the paint from the sun

Just came across this video. Mine did the same so it’s a little awkward but close.

Great work brother! Loved the simplicity of your video.

❤

Not bad for do it yourself but as a professional i would so some things different but expensive compared to yours Lol

They some stuff i used in between valley and pan that expans after use works very well

If you measure from where you end to where you start top and bottom same you will never saw tooth bottom

They still a vent you can use for metal

Venting in Florida is so important

2 inches off bottom prity tight with no room for error

In flats know because some contractors over tight the screws and the metal split

As a roofing contractor I've heard that before lol metal here is about 4 dollars a foot for instance a pan 5 ft 20 bucks

Super thank you bro

Run a plastic putty knife down the side to pop and pry the moulding off. Wash away whatever debri you can wish dish soap and water and then use decal remover wheel on a drill to get the adhesive off. Had both sides done in no time.

Where is the fuse on a Yamaha quad four

Thank you so much for this! Did you remove the fuel pump fuse and relay first? I’ve got over a half a tank of fuel, should I wait until it’s near empty?

Hello where can I buy those hinges for my 2005 yukon 5.3 motor I thank you in advance.

I never missed one video of yours,the food you made for your family looks very delicious and healthy,you are blessed to have an extraordinary talent,thanks for sharing your life with us

The purpose t I build anything is to use the best options for the best outcome. I hate the use of cheap materials that go into the construction of houses. It makes sense to use materials that won't need replacement for decades, giving homeowners more time enjoying their homes rather fixing damages that were avoidable or hiring someone that may rob them. Thank you the video.

Hey man. I appreciate the video. This with help me with my upcoming roof repair. Thanks again.

👀👍🏼

Watched and used your video great. On question when you got to the top and slid the last repair shingle up under the existing shingle how were you able to nail it? thanks

Thanks for the vid, if you just have a little block you dont even have to jack the car. Get a hose with a jet nozzle and point it up there in the general vicinity next to the cat and blast while sweeping it a bit. Itll usually break up the clog and takes all of 20 seconds.

Thats what i thought watching this....

When did you do the roof job? How is it holding up?

This is absolute genius!

That’s a bad design by GM.

Tapping metal to metal, no bueno! Put at least rag or shop towel inbeteen…playing with gas fumes bud…

Thanks for this. My Trailblazer needs this fix. Going forward I don't think I'll open the glass, unless I nee to stick wood out the back or something.

I just bought one at a junk yard for $80, for my 03 tahoe. My melted from one of the hinges.

Man I wish I could upload my video in your comments but I followed your procedure and it’s not the prettiest but I feel sure it’s gonna save me that 800 bucks

Why was no flet put down over the roof patch?

What was the car doing or not doing? Mine drives for 10 minutes and stalls

Exelente information gracias,

Good job

If anyone is doing metal work like this get the set of DeWalt shears from lowes and after getting the first pitch use a chalk line and center of rib to center of rib is typically 36 inches

How tall is your ladder?

I’m not specialize on roofing work at all, and had learned a lot from your video. However, I do believe that you forgot to place waterproof tar paper before you place shingles back to that area?!

Removed side panels from my Suburban. What a pain in the arse! Took at least one hour (per door) using heat gun, WD-40, brake cleaner, Goo Gone, scrapers and fingernails!

He did it wrong the underlay goes first before shingles